pdf-icon

CONTENTS

M5Camera-X

SKU:U038

Preview
Preview
Preview
Thumbnail
Thumbnail
Thumbnail

Description

M5CameraX is a development board for image recognition. It features an ESP32(4M Flash + 520K RAM) chip and 2-Megapixel camera (OV2640).M5Camera offers plenty of storage, with an extra 4 Mbyte PSRAM. It also supports image transmission via Wi-Fi and debugging through USB Type-C port.

The hardware comes preloaded software, programmed by ESP-IDF. It is an application to run Wi-Fi camera. The output image is size 600*800, since it's 2MP, you sure can optimize the software to output the maximum size of photos.

what this software can do?

  • Power the board via USB type-C or GROVE
  • Use your phone to Wi-Fi scan an AP name start with 'm5stack-' and click to connect this AP.
  • Open up web browser on your phone and visit 192.168.4.1
  • Then here comes the picture. Video is about 5-6 frames per seconds. not super fast.
This product is EOL now.

Features

  • CP2104 USB-to-TTL converter
  • ESP32-WROVER (PCB Antenna)
  • WIFI image transmission
  • OV2640 sensor

Include

  • 1x M5CameraX
  • 1x LEGO Adapter
  • 1x Wall-1515
  • 1x Type-C USB(20cm)

Specifications

Resources Parameter
RAM 4MB
Flash 4M
Image Sensor OV2640
Maximum resolution 2M pixel
Output format YUV(422/420)/YCbCr422,RGB565/555,8-bit compressed data,8-/10-bit Raw RGB data
FOV 65°
CCD Size 1/4 inch
Net weight 14g
Gross weight 38g
Product Size 24*48*13mm
Package Size 75*45*30mm

EasyLoader

download EasyLoader

What is EasyLoader?
1.EasyLoader is a simple and fast program burner. Every product page in EasyLoader provides a product-related case program. It can be burned to the master through simple steps, and a series of function verification can be performed. .
  1. After downloading the software, double-click to run the application, connect the M5 device to the computer through the data cable, select the port parameters, click "Burn" to start burning. (For M5StickC burning, please Set the baud rate to 750000 or 115200)

PinMap

Camera Interface PinMap

*Interface* *Camera Pin* *M5Camera(B model)*
SCCB Clock SIOC IO23
SCCB Data SIOD IO22
System Clock XCLK IO27
Vertical Sync VSYNC IO25
Horizontal Reference HREF IO26
Pixel Clock PCLK IO21
Pixel Data Bit 0 D2 IO32
Pixel Data Bit 1 D3 IO35
Pixel Data Bit 2 D4 IO34
Pixel Data Bit 3 D5 IO5
Pixel Data Bit 4 D6 IO39
Pixel Data Bit 5 D7 IO18
Pixel Data Bit 6 D8 IO36
Pixel Data Bit 7 D9 IO19
Camera Reset RESET IO15
Camera Power Down PWDN *see Note 1*
Power Supply 3.3V 3V3 3V3
Ground GND GND

GROVE Interface

*Grove* *M5Camera*
SCL IO13
SDA IO4
5V 5V
GND GND

LED Interface

LED *M5Camera*
LED_Pin IO14

The following tables are Reserved Chip Interfaces

BME280 Interface

*It's I2C address is 0x76.*

*BME280* *M5Camera*
SCL IO23
SDA IO22

MPU6050 Interface

*It's I2C address is 0x68.*

*MPU6050* *M5Camera*
SCL IO23
SDA IO22

MIC(SPM1423) Interface

*MIC(SPM1423)* *M5Camera*
SCL IO2
SDA IO4

NOTE:

  1. Camera Power Down pin does not need to be connected to ESP32 GPIO. Instead it may be pulled down to ground with 10 kOhm resistor.

View M5 camera series/product differences

Schematics

Power circuit

Chip peripheral circuit

USB to serial port part of the circuit

ソフトウェア

Firmware

Arduino

Code

Source Code