M5Camera-F New
Description
M5Camera-F New is a fisheye wide-angle image recognition development board with a field of view of 150°. It integrates the ESP32 (4M Flash + 520K RAM + 4M PSRAM) chip and a 2MP camera (OV2640). It supports WiFi image transmission and USB port debugging.
The hardware comes pre-installed with firmware, and it can be programmed and developed using ESP-IDF to run the WiFi-camera application. The default program outputs an image size of 600 x 800, but you can optimize the program to output larger sizes.
How to use this program?
- Turn on your phone's Wi-Fi, scan and connect to the AP hotspot with a name starting with "m5stack-".
- Open your phone's browser and visit 192.168.4.1 to access the monitoring page and get real-time video footage.
- The video frame rate is approximately 5-6 frames per second.
Since the module can generate a WIFI hotspot AP, you can use a phone, PC, or other devices to wirelessly obtain camera images via WIFI, or you can obtain camera images via the module's HY2.0-4P interface.
Features
- Based on ESP32 design
- WIFI image transmission
- CP2104 USB TTL
- Wide-angle lens 150°
- OV2640 visual sensor
Includes
- 1 x M5Camera-F New
- 1 x LEGO adapter clip
- 1 x Wall/1515
- 1 x USB Type-C cable (20cm)
Specifications
| Specification | Parameter |
|---|---|
| Flash | 4M |
| RAM | 4MB |
| Image Sensor | OV2640 |
| Maximum Resolution | 2MP |
| Output Format | YUV (422/420) /YCbCr422, 8-bit compressed data, RGB565/555, 8-/10-bit Raw RGB data |
| Field of View | 150° |
| CCD Size | 1/4 inch |
| Net Weight | 17g |
| Gross Weight | 41g |
| Product Dimensions | 24 x 48 x 19mm |
| Package Dimensions | 75 x 45 x 30mm |
Schematics
Power Circuit
Chip Peripheral Circuit
USB to Serial Circuit
PinMap
Camera
| Interface | Camera Pin | M5CameraF |
|---|---|---|
| SCCB Clock | SIOC | IO23 |
| SCCB Data | SIOD | IO22 |
| System Clock | XCLK | IO27 |
| Vertical Sync | VSYNC | IO25 |
| Horizontal Reference | HREF | IO26 |
| Pixel Clock | PCLK | IO21 |
| Pixel Data Bit 0 | D2 | IO32 |
| Pixel Data Bit 1 | D3 | IO35 |
| Pixel Data Bit 2 | D4 | IO34 |
| Pixel Data Bit 3 | D5 | IO5 |
| Pixel Data Bit 4 | D6 | IO39 |
| Pixel Data Bit 5 | D7 | IO18 |
| Pixel Data Bit 6 | D8 | IO36 |
| Pixel Data Bit 7 | D9 | IO19 |
| Camera Reset | RESET | IO15 |
| Camera Power Down | PWDN | see Note 1 |
| Power Supply 3.3V | 3V3 | 3V3 |
| Ground | GND | GND |
HY2.0-4P Interface
| HY2.0-4P | M5CameraF |
|---|---|
| SCL | G4 |
| SDA | G13 |
| 5V | 5V |
| GND | GND |
LED
| LED | M5Camera |
|---|---|
| LED_Pin | IO14 |
The PIN8 (PDWN) of the OV2640 chip is the enable pin. In this motherboard, it is enabled by a 12KΩ pull-down resistor to ground, entering the working mode. When PIN8 (PDWN) is pulled high, it will enter Camera Power Down mode.
The PIN8 (PDWN) of the OV2640 chip is the enable pin. In this motherboard, it is enabled by a 12KΩ pull-down resistor to ground, entering the working mode. When PIN8 (PDWN) is pulled high, it will enter Camera Power Down mode.
Datasheets
Softwares
Arduino
ESP-IDF
- M5Stack-Camera
- M5CameraF Firmware
- UART Communication-M5CameraF**
- UART Communication-M5Core
- QR Code Recognition
- MPU6050
EasyLoader
| Easyloader | Download Link | Notes |
|---|---|---|
| M5Camera-F New AP Firmware Easyloader | download | / |